STR Performance lightweight flywheel for...
STR Performance lightweight flywheel for...
STR Performance lightweight flywheel for Volkswagen Golf 2 Corrado 1.8 G60 including Syncro and Rallye 02A 228mm
STR Performance lightweight flywheel for Volkswagen Golf 2 Corrado 1.8 G60 including Syncro and Rallye 02A 228mm

STR Performance lightweight flywheel for Volkswagen Golf 2 Corrado 1.8 G60 including Syncro and Rallye 02A 228mm

vgm14357
In stock
€299.95
Tax included

Here is our 4.1 kg STR Performance lightweight flywheel for Volkswagen Volkswagen Golf 3 4 Bora / Audi A3 8L / Skoda Fabia 1.9 TDI 90hp 110hp 2 wheel drive 5-speed gearbox 02J 02A 228mm

 Customer ratings and reviews
Nobody has posted a review yet
in this language
 

This lightened and reinforced High Performance flywheel from STR Performance , significantly optimizes engine revolutions as well as the distribution of weight between the front and rear of the crankshaft in terms of inertia on Volkswagen Golf 3 4 Bora engines. / Audi A3 8L / Skoda Fabia 1.9 TDI 90hp 110hp 2 wheel drive 5-speed gearbox 02J 02A 228mm

Only compatible for 1.9 TDI 90hp 110hp transverse engine (not compatible audi A4 B5, A6) 5-speed gearbox 02A 02J clutch 228mm

Benefits of our lightweight single-mass flywheel:

  • our steering wheel weighs only 4.6 kg, the original steering wheel 9 kg
  • all our flywheels are made of chrome molybdenum steel G 1.75, extremely suitable for high speed engines
  • homologated without limitation of CV
  • significantly improved acceleration due to less flywheel mass
  • the engine revs up faster, no loss of performance.
  • suitable for motorsport and production vehicles
  • less fuel consumption
  • reduces response lag typical of turbo engines
  • precision balancing, bearings are less affected, fine balanced according to DIN ISO 1940
  • including starter crown
  • compatible with both a standard clutch and a high performance clutch
  • made in germany
  • integrated release crown

Here are the assembly instructions:

Preparation :

The friction surface of the flywheel, the threads of the crankshaft, the crankshaft screws (only if these do not have a threadlocker) and the clutch screws must be cleaned of grease, dirt and grease. dust with a cleaner (e.g. brake cleaner), otherwise the clutch may slip after installation.

Screws with thread lock must be used with "medium strength" loctite.

Flywheel screws:

  • Make sure they are screwed tightly into the thread.
  • First tighten by hand then tighten evenly "crosswise" to 116Nm with a torque wrench.
  • (1st pass about 65 Nm - 2nd pass 116 Nm)
  • The friction surfaces (organic and sintered) are equipped with a "spring cage".
  • In order not to impair the operation of the clutch, the friction disc must be fitted with the side of the spring cage facing the flywheel.
  • The friction disc is centered on the flywheel using a centering mandrel (not supplied).
  • Then the pressure plate is pressed onto the flywheel spindles and screwed on.
  • It is important to ensure that the friction disc is centered if no centering mandrel is available for mounting.
  • Screw the pressure plate with the cleaned screws
2 Items

STR Performance

Free Newsletter!

Subscribe to our newsletter to receive our news

Follow us :
Livraison rapide

24 à 48 h
Si produit en stock

RETOUR PRODUIT

POSSIBLE
Sous 14 jours

HOTLINE

EXPERT HOTLINE
à votre écoute

PAIEMENT Sécurisé

Monetico - CIC
Cofidis - Paypal

Product added to compare.