Here are our camshafts fromCat Cams ForCITROEN 4 cylinders 1.3L 8vengine code TU3FJ2
Description :
The camshaft fromCat CamsWill allow you to considerably increase the performance of your vehicle.
When a vehicle must receive extensive mechanical preparation to obtain results worthy of the name and above all a significant range of progression, work on the camshafts becomes inevitable.
When preparing the camshaftCat Cams, we observe two modifications: the valve lift as well as the opening angle.
Valve lift allows you to change the length and opening angle, which causes less or more air to enter the combustion chamber.
You should know that more air entering therefore modifies the air/fuel mixture in the cylinders, which increases power at high revs.
Also, the greater the opening angle of the valve, the more the air flow increases, which promotes the air/fuel mixture and therefore more power.
Therefore for use in competition, leisure, circuit and other, the revs will be sharper, the character of your engine will be more furious and thus you will benefit from a better range of use which will become a real asset.
Without broaching the subject of driving pleasure which will increase your sensations tenfold.
Camshaft profile available forCITROEN 4 cylinders 1.3L 8v engine code TU3FJ2
Sports profile :
-
CamshaftCat CamsReference:4900602/C / Opening 0.1mm, intake 281°, exhaust 281° / Opening 1.0mm, intake 239°, exhaust 239° / Max lift intake 11.15mm, exhaust 11.15mm / Lift at TDC intake 1.20mm, exhaust 1.20mm / Full intake opening 114 °, exhaust 114°.
Bearing diameters: 44.12 - 43.62 - 43.12 - 42.62 - 36.92 mm (large bearings).
- CamshaftCat CamsReference:4900640/C / Opening 0.1mm, intake 279°, exhaust 279° / Opening 1.0mm, intake 242°, exhaust 242° / Max lift intake 10.90mm, exhaust 10.90mm / Lift at TDC intake 2.20mm, exhaust 2.20mm / Full intake opening 111 °, exhaust 111°.
Bearing diameters: 44.12 - 43.62 - 43.12 - 42.62 - 36.92 mm (large bearings)#ECU reprogramming required.
Rally and circuit profile:
- CamshaftCat CamsReference: 4900645/C/ Opening 0.1mm inlet 280°, exhaust 280° / Opening 1.0mm, inlet 244°, exhaust 244° / Max lift inlet 11.25mm, exhaust 11.25mm / Lift at TDC inlet 2.65mm, exhaust 2.65mm / Full opening inlet 109° exhaust 109° Hydraulic Lifters.
Bearing diameters: 44.12 - 43.62 - 43.12 - 42.62 - 36.92 mm (large bearings). The distance between the valve and the piston must be at least 1.0 mm: - check 5-15° after TDC on intake - check 5-15° before TDC on exhaust. Machine the pistons if necessary. Improper installation can cause serious engine damage! ONLY for track applications and professional street use with engine management or adjustable carburetors.
- CamshaftCat CamsReference:4900671/C/ Opening 0.1mm inlet 293°, exhaust 293° / Opening 1.0mm inlet 250°, exhaust 250° / Max lift inlet 11.45mm, exhaust 11.45mm / Lift at TDC inlet 3.15mm, exhaust 3.15mm / Full inlet opening 108°, exhaust 108°.Attention modifications to be expected : upper cup reference 99316/H, external spring reference PAC-S10011.
Bearing diameters: 44.12 - 43.62 - 43.12 - 42.62 - 36.92 mm (large bearings). FOR COMPETITION REQUESTS ONLY. The following details should be checked: - The camshafts should turn smoothly in the cylinder head, ensuring free stroke by machining where necessary - The distance between the valve seal and the retainer at full lift should be d 'at least 0.6 mm - A minimum valve spring travel of 1.0 mm at full lift must be provided - distance between valve and piston 1.0 mm (pref. 1.5 mm). check 5-15° before TDC on the exhaust, and after TDC on the intake. For use ONLY in competition engines with independent engine management (throttle position sensor) or carburettors.
- CamshaftCat CamsReference5502361/C/ Opening 0.1mm, intake 282°, exhaust 274° / Opening 1.0mm, intake 244°, exhaust 236° / Max lift intake 11.50mm, exhaust 11.00mm / Lift at TDC intake 2.95mm, exhaust 2.40mm / Full opening intake 108°, exhaust 108°Please note changes to be expected:Valve springsReference PAC-D92009,PushersMechanical. CC002 Clearance: Inlet 0.20mm, exhaust 0.20mm,Cups99337,Lozenges CC-TRE004
- CamshaftCat CamsReference5502362/COpening 0.1mm inlet 290°, exhaust 282° / Opening 1.0mm inlet 252°, exhaust 244° / Max inlet lift 12.00mm, exhaust 11.50mm / Lift at TDC inlet 3.75mm, exhaust 3.20mm / Full inlet opening 106 °, exhaust 106°Please note changes to be expected:Valve springsReference PAC-D92009,PushersMechanicalReference CC002 Clearance: intake 0.20mm, exhaust 0.20mm,Cups99337,Lozenges CC-TRE004
- CamshaftCat CamsReference:5502363/C/ intake 298°, exhaust 290° / Opening 1.0mm, intake 260°, exhaust 252° / Max lift intake 12.50mm, exhaust 12.00mm / Lift at TDC intake 4.55mm, exhaust 4.00mm / Full intake opening 104 °, exhaust 104°Please note changes to be expected:Valve springsReference PAC-D92009, PushersMechanical. CC002 Clearance: intake 0.20mm, exhaust 0.20mm,Cups99337,LozengesCC-TRE004
- CamshaftCat CamsReference5502364/C/ Opening 0.1mm intake 307°, exhaust 298° / Opening 1.0mm, intake 268°, exhaust 260° / Max lift intake 13.00mm, exhaust 12.50mm / Lift at TDC: intake 5.10mm, exhaust 4.50mm / Full opening inlet 104°, exhaust 104°Please note changes to be expected:Valve springsReference PAC-D92009,PushersMechanical. CC002 Clearance: intake 0.20mm, exhaust 0.20mm,Cups 99337,LozengesCC-TRE004
- CamshaftCat CamsReference5502301/C/ Opening 0.1mm inlet 288°, exhaust 274° / Opening 1.0mm inlet 2580, exhaust 249° / Lift at max intake 12.45mm, exhaust 11.90mm / Lift at TDC intake 3.55mm, exhaust 2.95mm / Full opening inlet 110°, 110° exhaustPlease note changes to be expected:Valve springsReference PAC-D92009PushersMechanical. CC002 Clearance: intake 0.10mm, exhaust 0.15mm,Cups99337,LozengesCC-TRE004
- CamshaftCat CamsReference4900604/C / Opening 0.1mm: intake 288°, exhaust 287° / Opening 1.0mm intake 262°, exhaust 254° / Max lift intake 12.50mm, exhaust 12.00mm / Lift at TDC intake 4.50mm exhaust 3.95mm full intake opening 106° exhaust 106°.Please note changes to be expected:Valve springsReference PAC-D92009,PushersMechanicalCC002 Clearance: intake 0.20mm, exhaust 0.20mm,Cups99337,LozengesCC-TRE004
Group N FIA profile:
- CamshaftCat Cams reference 4900604/C / Opening 0.1mm intake 261°, exhaust 263° / Opening 1.0mm intake 226, exhaust 226° / Lift at max intake 10.60mm, exhaust 10.60mm / Lift at TDC intake 1.15mm, exhaust 1.20mm / Full opening intake 114°, exhaust 113°.
Bearing diameters: 44.12 - 43.62 - 43.12 - 42.62 - 36.92 mm (large bearings). GN FIA sheet nr. 5445 (AX GTi 1360cc) / 5453 (106 Rallye 1294cc). When ordering, please indicate whether the camshaft must meet all approval measures.
/!\ ATTENTION /!\
The camshafts are custom-made parts.
Therefore, we will not carry out returns, exchanges or refunds in the event of an error.
To avoid any inconvenience, please ensure the correct compatibility of the camshafts and or contact us.
